ISO 5817:2023

مواصفة قياسية دولية   الإصدار الحالي · اعتمدت بتاريخ ٢٤ فبراير ٢٠٢٣

Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections

ملفات الوثيقة ISO 5817:2023

الإنجليزية 26 صفحات
الإصدار الحالي
164.18 USD

مجال الوثيقة ISO 5817:2023

This document specifies quality levels of imperfections in fusion-welded joints (except for beam welding) in all types of steel, nickel, titanium and their alloys. It applies to material thickness ≥ 0,5 mm. It covers fully penetrated butt welds and all fillet welds. Its principles can also be applied to partial-penetration butt welds.

Quality levels for beam-welded joints in steel are presented in ISO 13919-1.

Three quality levels are given in order to permit application to a wide range of welded fabrication. They are designated by symbols B, C and D. Quality level B corresponds to the highest requirement on the finished weld.

Several types of loads are considered, e.g. static load, thermal load, corrosion load, pressure load. Additional guidance on fatigue loads is given in Annex B.

The quality levels refer to production and good workmanship.

This document is applicable to:

a)       non-alloy and alloy steels;

b)       nickel and nickel alloys;

c)        titanium and titanium alloys;

d)       manual, mechanized and automatic welding;

e)       all welding positions;

f)         all types of welds, e.g. butt welds, fillet welds and branch connections;

g)       the following welding processes and their sub-processes, as defined in ISO 4063:

     11 metal arc welding without gas protection;

     12 submerged arc welding;

     13 gas-shielded metal arc welding;

     14 gas-shielded arc welding with non-consumable tungsten electrode;

     15 plasma arc welding;

     31 oxyfuel gas welding (for steel only).

Metallurgical aspects, such as grain size and hardness, are not covered by this document.

الأكثر مبيعاً

GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
YSMO GSO 150-2:2020
GSO 150-2:2013 
لائحة فنية يمنية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
YSMO GSO 2055-1:2020
GSO 2055-1:2015 
مواصفة قياسية يمنية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال
GSO 2055-1:2015
 
لائحة فنية خليجية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال

اعتمدت مؤخراً

ISO 6182-18:2025
 
مواصفة قياسية دولية
Fire protection — Automatic sprinkler system — Part 18: Requirements and test methods for flexible sprinkler hose
ISO 8426-1:2025
 
مواصفة قياسية دولية
Hydraulic fluid power — Determination of derived displacement of positive displacement pumps and motors — Part 1: Two-step Toet method
ISO 21121:2025
 
مواصفة قياسية دولية
Spices and condiments — Dried lime (whole, slices and ground) — Specification
ISO 15614-2:2025
 
مواصفة قياسية دولية
Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 2: Arc welding of aluminium and its alloys