GSO IEC 60670-24:2014
IEC 60670-24:2011
Gulf Standard
Current Edition
·
Approved on
25 December 2014
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations - Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment
GSO IEC 60670-24:2014 Files
No files are available for this standard right now!
GSO IEC 60670-24:2014 Scope
Replacement:
This part of IEC 60670 applies to enclosures and parts of them for housing protective devices
and other power dissipating electrical equipment intended to be used with a rated voltage not
exceeding 400 V and a total incoming load current not exceeding 125 A for household and
similar fixed electrical installations.
These enclosures are intended to be installed where unskilled persons have access. They are
intended to be integrated with electrical equipment on site by skilled persons (installers).
They are intended to be installed where the prospective short circuit current does not exceed
10 kA unless they are protected by current limiting protective devices with a cut-off current not
exceeding 17 kA.
Enclosures complying with this standard are suitable for use, after installation, at ambient
temperature not normally exceeding 25 °C, but occasionally reaching 35 °C over 24 h, max.
40 °C and min. –5 °C.
An enclosure which is an integral part of an electrical accessory and provides protection
against external influences (e.g. mechanical impacts, ingress of solid objects or of water), is
covered by the relevant standard for such an accessory.
This standard does not apply to a low-voltage switchgear and controlgear assembly
(ASSEMBLY) as defined in the IEC 60439 or IEC 61439 series of standards nor to a main
entrance panel which may or may not be part of the distribution board.
NOTE 1 A main entrance panel is a set composed by a panel or an enclosure equipped with a meter and/or the
main incoming device. Main entrance panels comply with their appropriate standards or the requirements of the
local supplier if any.
NOTE 2 In the following country this standard cannot be used in installations with a 230 V single-phase supply
rated up to 100 A that is under the control of ordinary persons. Integration of mechanical and electrical devices into
an enclosure must be verified by compliance with IEC 60439-3 [British standard EN 60439-3]: UK.
NOTE 3 In the following country this standard can only be used for GP enclosures with the instructions according
to Annex A. For the other types of enclosures the integration of mechanical and electrical devices into an enclosure
is verified by compliance with DS EN 60439-3: DK.
Best Sellers From Electrical Sector
YSMO GSO 2530:2023
GSO 2530:2016
Yemeni Technical Regulation
Energy Labelling And Minimum Energy Performance Requirements For Air-Conditioners
GSO 2530:2016
Gulf Standard
Energy Labelling And Minimum Energy Performance Requirements For Air-Conditioners
GSO 34:2007
Gulf Technical Regulation
LEAD-ACID STARTER BATTERIES USED FOR
MOTOR VEHICLES AND INTERNAL
COMBUSTION ENGINES
GSO 35:2007
Gulf Standard
Methods of test
for lead-acid starter batteries used for motor vehicles
and internal combustion engines
Recently Published from Electrical Sector
GSO 2770:2024
Gulf Standard
WATER HEATERS - ENERGY PERFORMANCE REQUIREMENTS
GSO IEC 61508-7:2024
IEC 61508-7:2010
Gulf Standard
Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures (see Functional Safety and IEC 61508)
GSO IEC 62148-17:2024
IEC 62148-17:2023
Gulf Standard
Fibre optic active components and devices - Package and interface standards - Part 17: Transmitter and receiver components with dual coaxial RF connectors
GSO IEC 63027:2024
IEC 63027:2023
Gulf Standard
Photovoltaic power systems - DC arc detection and interruption